GERMAN STAINLESS STEEL
Made in Germany
BONTEMPI manufactures its products using controlled materials that are compatible with their specific intended use.
We take care to ensure that the materials used meet the requirements set out in the specific product standards, where applicable. Below is a list of the materials we use in production, along with a brief description of the characteristics of each.
The “Technical Data Sheet” of each item specifies the grade of steel considered most suitable based on company experience and the required characteristics. The “Own Brand Labeller” agreement signed with the supplier guarantees that the supplier retains the Material Certificate and that the materials used to manufacture the devices supplied to BONTEMPI are biologically compatible.
GENERAL REPORT ON MATERIALS USED
Stainless Steels
Stainless steels are alloys based on iron, chromium, and carbon, along with other elements such as nickel, molybdenum, silicon, and titanium, which make them particularly resistant to corrosion. According to standards, stainless steels are defined as those with a chromium percentage of at least 11%.
Stainless steels can be divided into three families based on their distinguishing metallurgical structure:
MARTENSITIC: hardenable by heat treatment;
FERRITIC: stable structure regardless of temperature;
AUSTENITIC: stable austenitic structure regardless of temperature.
Martensitic steels have a C content between 0.1% and 0.5%, with peaks up to 1%, and a Cr content
approximately between 11% and 18%. Ferritic steels have a Cr content between 16% and 30% and very low C levels below 0.1%.
Austenitic steels contain 15–26% Cr as well as 6–22% Ni and very low C levels up to a maximum of 0.2%.
One of the distinctive features of stainless steels is precisely their resistance to corrosion; however, this should not be understood in absolute terms. Rather, the use of each stainless steel grade must be calibrated according to the working environment and the mechanical properties required, which directly influence the active or passive state of the stainless steel.
AISI (American Iron and Steel Institute)
Austenitic Stainless Steels (AISI 300 series):
They are not hardenable, but exhibit excellent corrosion-resistant properties.
They are typically used for handles where there are no specific hardness requirements.
Specific materials in this family with good elastic properties are also used for certain types of probes. The “Own Brand Labeller” agreement signed with the supplier guarantees that the supplier verifies the material certificate of origin to ensure that the mechanical properties of the material fall within the acceptance range specified in the classification tables.
Martensitic Stainless Steels (AISI 400 series)
These are essentially straight chromium steels (11%–18%) possibly containing small amounts of other elements. A key characteristic of these steels is their ability to improve their mechanical properties through quenching and tempering heat treatments; by varying the temperatures, good mechanical properties can be balanced with good corrosion resistance. Some martensitic stainless steels exhibit good high-temperature creep resistance up to 650°C, with good resistance to scaling in oxidizing environments up to 700°C.
Welding these steels presents some difficulty when the carbon content exceeds 0.15%–0.20%.
In all cases, sound welds can be achieved with appropriate preheating and annealing heat treatments. For electrode welding, it is advisable to use martensitic stainless steel electrodes.
Martensitic stainless steels are particularly suited for applications requiring high mechanical strength, hardness, and abrasion resistance combined with adequate corrosion resistance.
Main Steels for Surgical Instruments
AISI 420 STEEL
Martensitic steel with distinctive mechanical properties that make it suitable for a wide range of uses. In the hardened and tempered condition with mirror-polished surfaces, it exhibits good corrosion resistance in moderately aggressive non-chlorinated environments.
AISI 420C STEEL
Martensitic steel, hardenable to a hardness exceeding 52 HRC. Maximum corrosion resistance is achieved in the hardened, stress-relieved, and polished condition. It is not intended for use in welded components.
AISI 440A/B/C STEEL
Martensitic stainless steel with high C and Cr content and correspondingly high hardness after quenching (approx. 57 HRC). In the hardened and tempered condition and after polishing, it exhibits good corrosion resistance in air, fresh water, gasoline, and foodstuffs.
The carbon content of this stainless steel is approximately: A (0.75%), B (0.9%), C (1.2%). 440C is an excellent stainless steel, typically around 56–58 Rc, very hard, and with good edge retention.
Hardening and Tempering
The materials normally used for manufacturing surgical instruments are hardenable high-carbon chromium steels, “AISI (American Iron and Steel Institute) 440 and AISI 420”—that is, martensitic stainless steels containing at least 12% chromium—whose full potential can be developed through an appropriate manufacturing and heat-treatment cycle. Martensitic steels are alloys of iron, carbon, and chromium, to which other elements such as vanadium, molybdenum, nickel, and tungsten are very often added to improve and enhance corrosion resistance, hardness, and toughness. Optimal distribution, bonding, and melting of these elements together makes it possible to produce steel of superior quality.
Hardening (Quenching)
To make the best use of the potential of martensitic stainless steel, heat treatment or hardening is employed. Steel alloyed with other elements develops specific properties depending on the characteristics to be enhanced for its intended use.
In general, what transforms an alloy steel into an optimal cutlery steel is heat treatment (Hardening and Tempering). Every alloy steel is characterized by a critical temperature at which the crystal structure of the steel changes, increasing the solubility of carbon in the ferritic matrix: this temperature must be maintained to achieve austenitizing of the steel, yet not for so long as to promote grain growth.
The next step is rapid cooling (quenching) using various media (water, oil, salt emulsions, ice, air, etc.) to achieve the desired level of hardness.
Tempering
After hardening, the steel is very hard but also very brittle: to achieve a good balance between hardness (which translates into longer edge retention) and reduced brittleness (which translates into greater impact resistance), a second heat treatment (tempering) is always performed to stress-relieve the material subjected to the internal stress induced by hardening and to remove residual stresses.
Materials used during manufacturing
Various types of abrasives, vibratory finishing compounds, etc. are also used during production.
Any residues of these substances are thoroughly removed prior to final packaging through standard and ultrasonic cleaning.



Instrument Composition
CARBON - C
Present in all steels, it is the element that transforms iron into steel, defining the instrument’s elasticity while increasing hardness and cutting-edge durability. On average, steel must contain >0.5% carbon to be classified as “high-carbon steel”.
CHROMIUM - Cr
An element that increases resistance to wear, fatigue, and corrosion. Steel containing at least 13–14% chromium is generally considered “stainless” steel, although this definition is not entirely accurate because, despite its name, all steel can oxidize if no maintenance is carried out.
COBALT - Co
Increases strength and hardness, provides resistance to high temperatures, and enhances the effects of other alloying elements.
MANGANESE - Mn
An important element, as manganese helps the structure increase its hardenability and improves the steel, while deoxidizing and degassing metals during heat treatments.
MOLYBDENUM - Mo
Prevents embrittlement (Krupp’s disease / temper embrittlement) and, by increasing toughness and fatigue resistance, enhances machinability and corrosion resistance.
NICKEL - Ni
Increases hardness and strength. Nickel can also contribute to corrosion resistance, though it is certainly not as effective as chromium and would need to be used in high percentages at the expense of edge retention.
PHOSPHORUS - P
Reduces brittleness; in high concentrations it increases strength and machinability, resulting in greater strength and higher hardness.
ALUMINUM - Al
Used only for handles due to its good machinability and light weight. The material does not come into contact with the patient. There are no issues with sterilization.
TEFLON - (C2F4)n
Material with high biocompatibility. Used for internal components of forceps. Sterilization does not cause degradation of its properties.
TITANIUM - Ti
New titanium alloys deliver high performance: they are extremely resistant to oxidation, lightweight, abrasion-resistant, and non-magnetic. Due to the particular difficulty of machining them, they carry a higher cost.
TITANIUM NITRIDE - TiN
Material used as a non-stick coating on certain instruments employed for modeling pastes and composites.
TUNGSTEN CARBIDE - WC
It is used to increase the wear resistance of specific surfaces, such as on needle holders, forceps, and scissor blades, to extend cutting edge durability.
CERAMIC
Ceramic instruments, particularly scissors, feature extremely hard blades made from zirconia enriched with magnesium, silicon, and calcium. Ceramic offers unique characteristics such as above-average edge retention and maximum hygiene thanks to its inert material composition, which does not react with the tissues it contacts and is easy to clean.
PAINTS
Polyurethane-based paints are used to color-code parts of the handles of certain instruments for identification purposes. Once cured, the coating is stable and is unaffected by the agents normally present in the instrument’s operating environment. The patient never comes into contact with the paint, as it is not applied to the working surfaces but only to part of the handle. Healthcare professionals who properly wear latex gloves neither absorb any pigment nor compromise the paint layer. Therefore, the color coating has no effect on either the patient or the operator.
GOLD and GLASS
The former is used on specific products with particular aesthetic requirements, exclusively on the handles. In any case, the element is exceptionally well tolerated by the human body. The latter is used in the manufacture of mirrors. There are no issues with tissue compatibility or sterilization.
RHODIUM - Rh
Used to externally coat the reflective surface of mirrors. The material is resistant to acids and is inert.